|
|
|
| |
Icom F70/80 $750

|
|
Frequency range IC-F70T/S, F70DT/DS
IC-F80T/S, F80DT/DS |
136-174MHz
400-470MHz
450-520MHz |
| Number of channels |
256 channels / 32 zones |
| Channel spacing |
12.5kHz / 25kHz, 15kHz / 30kHz |
| PLL channel step |
2.5kHz, 3.125kHz (VHF)
5kHz, 6.25kHz (UHF) |
| Antenna impedance |
50Ω |
| Usable temperature range |
-30°C to +60°C;
-22°F to +140°F |
| Power supply requirement |
7.2V DC |
Output power and current drain (at 7.2V DC; approx.) |
| |
IC-F70, F70D |
IC-F80, F80D |
| Output Power |
5W |
4W |
| Transmit |
High |
2.2A |
2.4A |
| Low (1W) |
1.5A |
1.5A |
| Receive |
AF Max. |
450mA |
450mA |
| stand-by |
150mA |
150mA | |
| Dimensions (with battery pack) (Projections not included) |
58.6 (W) × 152 (H) × 38 (D) mm;
25/16 (W) × 531/32 (H) × 11/2 (D) in |
| Weight (approx.) |
400g; 14.1 oz (with BP-235)
430g; 15.6 oz (with BP-236) |
| Transmitter |
| Max. freq. deviation |
±5.0kHz (Wide)
+2.5Khz (Narrow) |
| Frequency Error |
±2.0ppm |
| Spurious emissions |
70dB typ. |
| Adjacent channel power |
70dB/60dB min. (Wide/narrow) |
|
FM Hum and Noise
VHF
UHF |
45/40dB typ. (Wide/narrow)
40/35dB typ. (Wide/narrow) |
| Audio harmonic distortion |
3% typ. (AF 1kHz, 40% deviation) |
| Modulation limiting |
60-100% of max. deviation |
| Ext. Microphone connector |
9-pin multi connector / 2.2kΩ |
| Receiver |
| Intermediate freq. |
1st 46.35
2nd 450kHz |
|
Sensitivity (typical)
Analog (12dB SINAD)
Digital (5% BER) |
0.25µV typ.
0.25µV typ. |
|
Squelch sensitivity
VHF
UHF |
0.25µV typ.
0.32µV typ. |
|
Adjacent Channel Selectivity Analog VHF Analog UHF
Digital VHF / UHF |
80/73dB typ. (Wide/narrow) 78/70dB typ (Wide/narrow) 60dB typ. |
|
Spurious response |
80dB/75dB typ. (VHF/UHF) |
| Intermodulation |
75dB (typ.) |
| Hum and noise ratio |
45/40dB typ. (Wide/narrow) |
| Audio output power |
500mW (at 10% distortion with an 8Ω load) |
| Ext. speaker connector |
9-pin multi connector / 8Ω |
Applicable U.S. Military Specifications
| Standard |
MIL 810 C |
MIL 810 D |
MIL 810 E |
MIL 810 F |
| Low Pressure |
500.1 |
I |
500.2 |
I, II |
500.3 |
I, II |
500.4 |
I, II |
| High Temp. |
501.1 |
I |
501.2 |
I, II |
501.3 |
I, II |
501.4 |
I, II |
| Low Temp. |
502.1 |
I |
502.2 |
I, II |
502.3 |
I, II |
502.4 |
I, II |
| Temp. Shock |
503.1 |
I |
503.2 |
I |
503.3 |
I |
503.4 |
I |
| Solar Radiation |
505.1 |
I |
505.2 |
I |
505.3 |
I |
505.4 |
I |
| Rain |
506.1 |
I, II |
506.2 |
I, II |
506.3 |
I, II |
506.4 |
I, II |
| Humidity |
507.1 |
I, II |
507.2 |
II, III |
507.3 |
II, III |
507.4 |
– |
| Salt Fog |
509.1 |
I |
509.2 |
I |
509.3 |
I |
509.4 |
– |
| Dust Blowing |
510.1 |
I |
510.2 |
I |
510.3 |
I |
510.4 |
I |
| Immersion |
512.1 |
I |
512.2 |
I |
512.3 |
I |
512.4 |
I |
| Vibration |
514.2 |
VIII, X |
514.3 |
I |
514.4 |
I |
514.5 |
I |
| Shock |
516.2 |
I, II, V |
516.3 |
I, IV |
516.4 |
I, IV |
516.5 |
I, IV |
Measurements made in accordance with EIA-152C/204D, TIA-603. All stated specifications are subject to change without notice or obligation.
Supplied Acessories
- VHF antenna*
- UHF antenna*
- Alligator-type belt clip, MB-94
- Battery pack, BP-235
*Antenna may differ according to version
The Smart Migration to an APCO P25 Digital Radio System
IPX7 waterproof protection
The water removal design from the speaker grill keeps the communication clear, no matter what the elements are. The ICF70/F80 series has waterproof construction that is sealed with waterproof gaskets. * According to the International Standard IEC60529 (2001). 1m depth for 30 minutes.
Built-in multiple signaling
Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone and BIIS capability to set up your own talk groups and quiet stand-by when others are talking. You can also set up selective calls to individuals or control a repeater.
Multiple 2-Tone, Multiple 5-Tone
Up to 10 2-Tone and 8 5-Tone codes can be decoded on a single memory channel. This is perfect for professionals who require multiple district paging on one channel. When a matched tone is received, the following items are programmable for each code.
- Bell icon
- Answer back
- Stun
- Beep sound
- Auto transmit
- Scan
Alphanumeric display
The large high contrast LCD clearly shows a variety of information with a full dot-matrix display. Program the display to show either 1 line with 12 characters or 2 lines with 24 characters. Status icons are displayed at the top and the functions assigned to the P buttons (P0–P3) are shown at the bottom of the display. The bottom of the LCD shows the assigned functions (see right)
Li-Ion battery pack
The large capacity 1600mAh Lithium-Ion (Li-Ion) battery pack, BP-235 provides a practical 8 hours* of operating time. Li-Ion batteries allow flexible charging and have almost no memory effect. * Typical operation Tx:Rx: Stand-by=5:5:90
Tactical group function
The tactical group function allows you to copy memory channels to the tactical zone (zone 32) and dynamically regroup memory channels. Using the optional zone copy cable, memory channels in the tactical zone can be transferred from a master radio to other radios.
Project 25 (P25) Digital Features
Upgrade to digital option
The IC-F70/F80 series offers you three choices to P25 digital compatibility. Choice one is P25 compliant from the factory. Choice two is a digital hardware radio and you can install the P25 activation software (EX-2785 J01) later. Choice three is analog only radio and you can install the DSP unit, UT-120 and P25 activation software (EX-2785 J01) later.

AES/DES digital encryption activation software
AES and DES are encryption standards required by public safety agencies. The IC-F70D, F80D series provide secure encryption with DES and AES accordingly when activatied with EX-2785 J02 (for DES) and EX-2785 J03 (for AES) activation software.
Interoperability
The IC-F70D, F80D series is APCO Project 25 (P25) compliant. It ensures interoperability with other manufacturer’s P25 digital radios in conventional mode. Program digital and/or analog FM modes per channel. The mixed mode scan allows you to detect and receive both analog FM and P25 digital modes and to transmit either mode depending on programming.
Built-in voice scrambler
The IC-F70/F80 series includes a built-in inversion type voice scrambler. When a more secure system is required, the optional voice scrambler unit UT-109 or UT-110 is available. * These voice scrambler functions are not available in digital mode.
MDC 1200 compatible
The following selective calling and ANI features are available with the built-in MDC signaling.
- PTT ID/Caller ID
- Radio check
- Selective call
- Call alert
- Emergency, emergency mic monitoring
- Emergency man down (with UT-124)
- Radio stun/revive
- 500 Aliases
- Status/message
- Call log
Intrinsically safe version
Intrinsically safe version approved by FM Approvals, is suitable for use in hazardous areas where flammable gasses or liquids are used.
Radio stun/kill and Power-on password function
The radio stun/kill functions disable a lost or stolen radio over the air, eliminating security threats from undesired listeners. The power-on password prevents unauthorized people turning on the radio.
Other features
- 256 memory channels with 32 zones
- Built-in audio compander
- 8 DTMF autodial memories
- Normal and priority scans
- Busy, repeater lockout functions
- Wide and narrow (25/12.5kHz) channel spacing is programmable
- Power ON password, and more...
ICOM F3/4 Conventional and Trunking $375
|
Frequency range
IC-F3GT/GS
IC-F4GT/GS |
136-150 MHz 146-174 MHz
400-430 MHz 440-470 MHz 470-500 MHz
490-512 MHz (USA) 490-520 MHz (others) |
| Number of channels |
100Ch or 40Ch(Varies according to version) |
| Channel spacing |
12.5 kHz, 20 kHz, 25 kHz 12.5/25kHz |
| Antenna impedance |
50Ω |
| Frequency error |
±0.0005% (EIA; IC-F3GT)
±0.00025% (EIA; IC-F4GT)
±1.5 kHz (ETS; 12.5 kHz)
±2 kHz (ETS; 25/20 kHz) |
| PLL channel step |
5 kHz, 6.25 kHz, 7.5 kHz |
| Power supply requirement |
7.2 V DC (Icom battery pack) |
|
Current drain (at 7.2 V DC) |
| Transmit |
at 5 W |
1.6 A (IC-F3GT/GS) |
| |
at 4 W |
1.5 A (IC-F4GT/GS) |
| |
at 1 W |
0.7 A (IC-F3GT/GS) |
| |
|
0.8 A (IC-F4GT/GS) |
| Receive |
at AF max |
250 mA |
| |
at stand-by |
70 mA | |
| Operating temp. range |
-30°C to +60°C; -22°F to +140°F (EIA)
-25°C to +55°C (ETS) |
|
Dimensions
(projections not included) |
54(W) × 132(H) × 35(D) mm
2 1⁄8(W) × 5 3⁄16(H) × 1 7⁄16(D) in |
|
Weight (with BP-209) |
370 g; 13.1 oz |
| Transmitter |
Output power IC-F3GT/GS IC-F4GT/GS |
5.0 W 4.0 W |
| Max. freq. deviation |
±2.5 kHz, ±5 kHz, ±4 kHz |
| Modulation limiting |
80-100% |
| Audio harmonic distortion |
3% max. (1 kHz/40% dev.)
5% max. (1 kHz/60% dev.) |
| Spurious emissions |
73 dBc (EIA)
Less than 0.25 µW (ETS) |
| Adjacent Ch. power |
60 dB typ. (EIA; 12.5 kHz)
70 dB typ. (EIA; 25 kHz)
60 dB (ETS; 12.5 kHz)
70 dB (ETS; 25/20 kHz) |
| Residual modulation |
40 dB typ. (EIA; 12.5 kHz)
45 dB typ. (EIA; 25kHz)
43 dB (ETS; 12.5 kHz)
45 dB (ETS; 25/20 kHz) |
| External MIC connector |
3-conductor 2.5 (d) mm (1⁄10″)/2.2 kΩ |
| Receiver |
|
Sensitivity IC-F3GT/GS IC-F4GT/GS |
0.25 µV (at 12 dB SINAD) 0.63 µV (at 20 dB SINAD) 0.3 µV (at 12 dB SINAD) 0.79 µV (at 20 dB SINAD) |
|
Squelch sensitivity
IC-F3GT/GS
IC-F4GT/GS |
(at threshold) 0.25 µV
0.3 µV |
| Adjacent Ch. selectivity |
65 dB typ. (EIA; 12.5 kHz) 75 dB typ. (EIA; 25 kHz)
60 dB (ETS; 12.5 kHz)
70 dB (ETS; 25/20 kHz) |
| Spurious response |
70 dB (EIA)
70 dB (ETS) |
| Intermodulation |
70 dB (EIA)
65 dB (ETS) |
| Hum and noise ratio |
40 dB typ. (EIA; 12.5 kHz) 45 dB typ. (EIA; 25 kHz)
43 dB (ETS; 12.5 kHz)
45 dB (ETS; 25/20 kHz) |
| Audio output power |
0.5 W at 5% distortion with an 8Ω load |
| External SP connector |
2-conductor 3.5 (d) mm (1⁄8″)/8Ω |
Applicable U.S. Military Specifications Icom makes rugged products that meet MIL-STD requirements and strict environmental standards as follows.
| Standard |
MIL 810 C |
MIL 810 D |
MIL 810 E |
MIL 810 F |
| Low Pressure |
500.1 |
I |
500.2 |
I, II |
500.3 |
I, II |
500.4 |
I, II |
| High Temp. |
501.1 |
I |
501.2 |
I, II |
501.3 |
I, II |
501.4 |
I, II |
| Low Temp. |
502.1 |
I |
502.2 |
I, II |
502.3 |
I, II |
502.4 |
I, II |
| Temp. Shock |
503.1 |
I |
503.2 |
I |
503.3 |
I |
503.4 |
I |
| Solar Radiation |
505.1 |
I |
505.2 |
I |
505.3 |
I |
505.4 |
I |
| Rain |
506.1 |
I, II |
506.2 |
I, II |
506.3 |
I, II |
506.4 |
I, II |
| Humidity |
507.1 |
I, II |
507.2 |
II, III |
507.3 |
II, III |
507.4 |
II, III |
| Salt Fog |
509.1 |
I |
509.2 |
I |
509.3 |
I |
509.4 |
I |
| Dust Blowing |
510.1 |
I |
510.2 |
I |
510.3 |
I |
510.4 |
I |
| Vibration |
514.2 |
VIII, X |
514.3 |
I |
514.4 |
I |
514.5 |
I |
| Shock |
516.2 |
I, II, V |
516.3 |
I, IV |
516.4 |
I, IV |
516.5 |
I, IV |
Measurements made in accordance with EIA/TIA-152C/204D, or ETS 300-086. All stated specifications are typical and subject to change without notice or obligation.
Supplied accessories
- VHF Antenna*
- UHF Antenna*
- Belt Clip
- Battery Pack, BP-209N
- Plastic Plate
*Antenna may differ according to version.
Durability, dependability, operation simplicity, style, ruggedness, economical use, and more are required for commercial transceivers. But only a few such transceivers are available, particularly for portables. Now from ICOM—the IC-F3G series of portable transceivers aim to become the most highly reputable of all commercials. Superior performance and features, everything you require is included. Icom's technology gives you satisfaction you never knew before.
Supports multiple signaling and flexible selective calling
CTCSS/DTCS encoder/decoder, and DTMF, 2/5-tone encoder with user programmable CTCSS, DTCS capabilities, are built-in. The optional UT-96+ (for 2/5tone), or UT-108+ (for DTMF) allows decode with ANI functions. In addition, special tone code, for group, and individual calls, and more features are available to support flexible, perfect selective calling operations.
- 7-digit code can be used as the 5-tone
- Direct individual station/group call with/without own ID transmission, or though repeater
- Selectable 5-tone format includes user tone format programming capability (Encode and Decode frequencies, Tone period, No-tone timer, and Tone length)
- Text or ID number indication
- Desired 5-tone code entering for both individual and group call
- Transceiver remote control—stun, kill, and scan start/stop functions
- Selectable comparing digit code for decoding
- Selective calling capability from a public telephone (UT-108 DTMF DECODER is required; base/repeater station must be connected to the public telephone network)
Man down function*
Automatically sending an emergency signal when the transceiver is left in the horizontal position for a preset time. *Optional UT-124+ is required.
Trunking capabilities*
Compatible with the SmarTrunk II™, or the LTR® trunking systems. *Optional UT-105+ for SmarTrunk IITM, UT-111+ for LTR® trunking is required.
Operation security
Optional voice scrambler units, UT-109+ and UT-110+, for secure communications are available.
Programmable key assign
Up to 8 programmable keys are available to assign specific functions. In particulqr, the red key can be used for important functions, such as an emergency call, etc.
Latest PC programming package
For Microsoft® Windows® 95/98.
MIL spec. durability
54(W) × 132(H) × 35(D) mm* compact body with durable, dependable construction, meets the MIL standard. *2 1⁄8(W) × 5 3⁄16(H) × 1 7⁄16(D) in
Simple operation
Enlarged 7-character alphanumeric automatic backlit LCD and function keys make for easier operation.
Long life batteries
The standard Ni-Cd battery pack allows 8 hours* operation. Optional battery pack for extended operation and a battery case for use while charging the battery, or for emergency operation etc., are available. *approx.; Tx:Rx:Standby ratio = 5:5:90
Other features
- 100 or 40 memory channels
- Powerful 5 W output for IC-F3GT/GS, 4 W output for IC-F4GT/GS
- Selectable channel attribute from emergency, priority A/B, and normal
- Normal and priority scans
- Auto LCD contrast
- 2 step power saver
- 5 autodialing memories for DTMF
- Busy, repeater lockout functions
- Power ON password, and more...
+only one of either unit can be installed.

Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S.A. and other countries. SmarTrunk II is a trademark of the SmarTrunk System, Inc. LTR is a registered trademark of the E.F.Johnson Company
|
|
|
|
| |
Icom F50/60 $425
All handhelds come with Li ion battery, antenna, and charger.

|
Frequency range IC-F50 IC-F60 |
136-174 MHz 400-470 MHz 450-512 MHz (U.S.A.) 450-520 MHz (General) |
| Number of Channels |
Max. 128 channels/ 8 banks |
| Channel spacing |
12.5/25kHz, 15/30kHz |
| Antenna impedance |
50 ohm (SMA Type) |
| Frequency error |
±2.5ppm |
PLL channel step IC-F50 IC-F60 |
2.5/3.125Khz 5/6.25KHz |
| Power supply requirements |
7.2V DC |
|
Current drain (approx.) Transmit Receive |
IC-F50 IC-F60 AF max. Stand-by |
1.5A/0.7A (5W/1W) 1.5A/0.8A (4W/1W) 300mA 85mA | |
| Operating temperature range |
–30°C to +60°C –22°F to +140°F |
Dimensions (W x H x D) (projections not included) |
56 x 97 x 36.4mm 2.2 x 3.8 x 1.4 in. |
| Weight (approx.) |
280g; 9.9oz |
| Transmitter |
Output power IC-F50 IC-F60 |
5.0W 4.0W |
| Modulation system |
Variable reactance frequency modulation |
| Max. frequency deviation |
±5kHz (wide) ±2.5kHz (narrow) |
| Modulation limiting |
60-100% of Max. deviation |
| Audio harmonic distortion |
3% typ. (AF 1kHz, 40% deviation) |
| Spurious emissions |
70dB Min. |
| Adjacent channel power |
70dB Min. (wide) 60dB Min. (narrow) |
| FM Hum and Noise |
46dB typ. (wide) 40dB typ. (narrow) |
| External microphone impedance |
9-pin multi connector/2.2kΩ |
| Receiver |
| Sensitivity (12dB SINAD) |
Less than 0.25 µV |
| Squelch sensitivity |
0.25µV typ. (at threshold) |
| Adjacent channel selectivity |
75dB typ. (wide) 65dB typ. (narrow) |
| Spurious response |
70dB |
| Intermodulation |
74dB typ. |
| Hum and noise |
45db typ. (wide) 40dB typ. (narrow) |
| Audio output power |
0.5W typ. at 10% distortion with an 8Ω load |
| External SP connector |
9-pin multi connector/8Ω |
Applicable U.S. Military SpecificationsIcom makes rugged products that meet MIL-STD requirements and strict environmental standards as follows.
| Standard |
MIL 810 C |
MIL 810 D |
MIL 810 E |
MIL 810 F |
| Low Pressure |
500.1 |
I |
500.2 |
I, II |
500.3 |
I, II |
500.4 |
I, II |
| High Temp. |
501.1 |
I |
501.2 |
I, II |
501.3 |
I, II |
501.4 |
I, II |
| Low Temp. |
502.1 |
I |
502.2 |
I, II |
502.3 |
I, II |
502.4 |
I, II |
| Temp. Shock |
503.1 |
I |
503.2 |
I |
503.3 |
I |
503.4 |
I |
| Solar Radiation |
505.1 |
I |
505.2 |
I |
505.3 |
I |
505.4 |
I |
| Rain |
506.1 |
I, II |
506.2 |
I, II |
506.3 |
I, II |
506.4 |
I, II |
| Humidity |
507.1 |
I, II |
507.2 |
II, III |
507.3 |
II, III |
507.4 |
– |
| Salt Fog |
509.1 |
I |
509.2 |
I |
509.3 |
I |
509.4 |
– |
| Dust |
510.1 |
I |
510.2 |
I |
510.3 |
I |
510.4 |
I |
| Vibration |
514.2 |
VIII, X |
514.3 |
I |
514.4 |
I |
514.5 |
I |
| Shock |
516.2 |
I, II, V |
516.3 |
I, IV |
516.4 |
I, IV |
516.5 |
I, IV |
Measurements made in accordance with EIA-152C/204D, TIA-603. All stated specifications are subject to change without notice or obligation.
Supplied Accessories
- VHF antenna*
- UHF antenna*
- Alligator-type belt clip, MB-98
- Battery pack, BP-227
*Antenna (Length may differ according to version)
Firefighters, Police, Security, Oil industry and Public utilities. Each profession has its own unique challenges, but all have one thing in common: the need for reliable communications. Icom’s IC-F50/F60 offers a compact waterproof, MIL STD package, that's easy to use. Rain or shine, this radio keeps you in contact in nearly any environment.
IPX7 waterproof protection
The gasket sealed waterproof housing provides superior waterproof protection, equivalent to IPX7*. Reliable and dependable use in harsh conditions such as rain, snow, sudden change in temperature, make the IC-F50/F60 the radio for all situations. * According to the international standard IEC 529 (1989). 1m depth for 30 minutes.
Built-in Tone signaling
Use the built-in CTCSS, DTCS, 2-Tone and 5-Tone capability to set up your own talk groups and quiet stand-by when others are talking. You can also set up selective calls to individuals or control a repeater.
Multiple 2-Tone, Multiple 5-Tone
Up to 10 2-Tone codes can be decoded on a single memory channel. This is perfect for professionals who require multiple district paging on one channel. When a matched tone is received, the following items are programmable for each code.
- Bell icon • Answer back
- Stun
- Beep sound
- Auto transmit
- Scan
Li-Ion battery pack
The large capacity 1700mAh Lithium-Ion (Li-Ion) battery pack, BP-227 provides a practical 10 hours* of operating time. Li-Ion batteries allow flexible charging and have almost no memory effect. * Typical operation Tx:Rx: Stand-by=5:5:90
Up to 7 programmable buttons
The [P0]–[P3], [Red] and [Up], [Down] buttons are programmable to meet specific needs. The [Red] button on the top panel can be assigned as an emergency trigger.
Alphanumeric display
The 8-character alphanumeric display shows channel, bank, tone code and scanning channel names on the display. 7 operational icons on the sub-line show various status at a glance.
Wide range coverage and large channel capacity
The IC-F50/F60 covers a wide frequency range in one version. The large capacity of 128 memory channels with 8 memory banks allows you to divide and store a variety of channels from local to wide area network channels. Both wide and narrow (25/12.5kHz) channel bandwidth is programmable to each channel.
Compact body
56(W)×97(H)×36.4(D) mm* compact body with durable, dependable construction, meets MIL standard specifications. * 2.2(W)×3.8(H)×1.4(D) in
Built-in voice scrambler
The IC-F50/F60 has a built-in inversion type voice scrambler in all versions. When a more secure system is required, versions with a rolling type voice scrambler* equivalent to the UT-110 are available. * Built-in, optional unit not required.
MDC 1200 Compatible
The following selective calling and ANI features are available with the built-in MDC signaling.
- PTT ID
- Radio check
- Caller ID
- Selective call
- Emergency, emergency mic monitoring
- Radio stun/revive
- 500 Aliases
- Status/message
- Call alert
Waterproof microphone
An optional waterproof speaker-microphone, HM-138 provides reliable operation, even with the radio securely on your belt.
Other features
- Built-in compander, compatible with the IC-F30G and IC-F520 series
- 8 DTMF autodial memories
- Powerful 5W output for IC-F50, 4W output for IC-F60
- Normal and priority scans
- 2 step power saver
- Optional AA alkaline battery case, BP-226 for battery back up
- Busy, repeater lockout function
- Power ON password, and more...
Icom F50V $625

|
| Frequency range |
136-174 MHz |
| Number of Channels |
Max. 128 channels/ 8 zones |
| Channel spacing |
12.5/25kHz |
| Antenna impedance |
50 Ω (SMA Type) |
| Frequency error |
±2.5ppm |
| PLL channel step |
2.5/3.125Khz |
| Power supply requirements |
7.2V DC |
|
Current drain (approx.) Transmit Receive |
5W 1W AF max. Stand-by |
1.8A 0.7A 500mA (Internal speaker) 350mA (External Speaker) 85mA | |
| Operating temperature range |
–30°C to +60°C –22°F to +140°F |
Dimensions (W x H x D) (projections not included) |
56 × 97 × 36.4mm 27⁄32 × 313⁄16 × 17⁄16 in. |
| Weight (approx.) |
280g; 9.9oz (With BP-227) |
| Transmitter |
| Output power |
5.0W |
| Modulation system |
Variable reactance frequency modulation |
| Max. frequency deviation |
±5kHz (wide) ±2.5kHz (narrow) |
| Modulation limiting |
60-100% of Max. deviation |
| Audio harmonic distortion |
3% typ. (AF 1kHz, 40% deviation) |
| Spurious emissions |
70dB typ. |
| Adjacent channel power |
70dB Min. (wide) 60dB Min. (narrow) |
| FM Hum and Noise |
46dB typ. (wide) 40dB typ. (narrow) |
| External microphone impedance |
9-pin multi connector/2.2kΩ |
| Receiver |
| Sensitivity |
0.25µV typ. (at 12db SINAD) |
| Squelch sensitivity |
0.25µV typ. (at threshold) |
| Adjacent channel selectivity |
75dB typ. (wide) 65dB typ. (narrow) |
| Spurious response |
70dB |
| Intermodulation |
74dB typ. |
| Hum and noise |
45db typ. (wide) 40dB typ. (narrow) |
| Audio output power |
0.7W typ. (Internal speaker) 0.5W typ. (external speaker) at 5% distortion with an 8Ω load |
| External SP connector |
9-pin multi connector/8Ω |
Applicable U.S. Military Specifications
Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and Ingress Protection standards.
| Standard |
MIL 810 C |
MIL 810 D |
MIL 810 E |
MIL 810 F |
| Low Pressure |
500.1 |
I |
500.2 |
I, II |
500.3 |
I, II |
500.4 |
I, II |
| High Temp. |
501.1 |
I |
501.2 |
I, II |
501.3 |
I, II |
501.4 |
I, II |
| Low Temp. |
502.1 |
I |
502.2 |
I, II |
502.3 |
I, II |
502.4 |
I, II |
| Temp. Shock |
503.1 |
I |
503.2 |
I |
503.3 |
I |
503.4 |
I |
| Solar Radiation |
505.1 |
I |
505.2 |
I |
505.3 |
I |
505.4 |
I |
| Rain |
506.1 |
I, II |
506.2 |
I, II |
506.3 |
I, II |
506.4 |
I, II |
| Humidity |
507.1 |
I, II |
507.2 |
II, III |
507.3 |
II, III |
507.4 |
– |
| Salt Fog |
509.1 |
I |
509.2 |
I |
509.3 |
I |
509.4 |
– |
| Dust |
510.1 |
I |
510.2 |
I |
510.3 |
I |
510.4 |
I |
| Vibration |
514.2 |
VIII, X |
514.3 |
I |
514.4 |
I |
514.5 |
I |
| Shock |
516.2 |
I, II, V |
516.3 |
I, IV |
516.4 |
I, IV |
516.5 |
I, IV |
| Ingress Protection Standard |
| Dust & Water |
IP67 (Dust-tight and waterproof protection) |
Measurements made in accordance with EIA-152C/204D, TIA-603. All stated specifications are subject to change without notice or obligation.
Supplied Accessories
- Antenna (Length may differ according to version)
- Alligator-type belt clip, MB-98
- Battery pack, BP-227
Vibration alert function
When a pre-programmed 2-tone/5-tone code or call from a specific user (MDC mode only) is received, the radio vibrates powerfully enough to be felt through heavy clothing.
8 minute voice recorder
When a pre-programmed 2-tone/5-tone code or a SelCall (MDC mode only) is received, the voice recorder automatically starts recording the incoming message. You will not miss an important call even when you are temporarily away from the radio. You can manually start recording incoming calls and also your own message. It records up to a maximum of 8 minutes (Or up to 48 calls of 10 sec. recording time).
700mW audio output
The IC-F50V delivers a loud 700mW* audio output with the built-in BTL amp. The built-in audio compander provides clear, low noise communications. Improved bass characteristics also betters the audio quality. * Typical with internal speaker.
Lone worker function for remote check in
When the radio is not operated for a preset period (1 to 255 min.), the radio sounds a beep and requires you to push the emergency button. If the emergency button is not pushed for a preset time (1 to 255 sec.), an emergency signal automatically transmits and informs your co-worker or dispatcher that something may have happened to the individual worker.
IP67, dust-tight and waterproof protection
The IC-F50V has outstanding protection against dust and water that is equivalent to IP67. The IC-F50V can withstand submersion in 1m depth of water for up to 30 minutes and has dust-tight construction that prevents the ingress of dust.
Most popular signalings built-in
Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone and MDC signaling capabilities to set up your talk group or selective calling. The IC-F50V can decode ten 2-Tone codes or eight 5- Tone codes on a channel. When a matched tone is received, the following actions are programmable for each code.
- Bell icon
- Answer back call
- Beep sound
- Auto transmit
- Radio Stun/Kill/Revive
- Voice recorder
- Vibration alert
MDC 1200 Compatible
The following selective calling and ANI features are available with the built-in MDC signaling.
- PTT ID
- Radio check
- Caller ID
- Call alert
- SelCall
- Emergency, emergency mic monitoring
- 500 Aliases
- Status/message
- Radio stun/revive
Mode dependent scan
In the mode dependent setting, the scanning setting is dependent on the operating channel. When you change the operating channel, the scanning list automatically changes to the operating channel setting. It is convenient when you move to a different operating area and change an operating channel, you don’t have to change the scanning setting.
Enhanced scanning
The Tx channel while scanning can be programmed per scanning list. The talk back function allows you to transmit on the channel detected after scanning resumes after a preset time, prior to the Tx channel setting. The nuisance delete function temporarily deletes a busy channel from the scanning list. Backlight at stop scan automatically turns on the LCD backlight when the scan stops.
Compact body
56(W)×97(H)×36.4(D) mm* compact body with durable, dependable construction, has been tested to MIL standard specifications. * 27⁄32(W)×313⁄16(H)×17⁄16(D) in
Li-Ion battery pack
The large capacity 1700mAh Lithium-Ion (Li-Ion) battery pack, BP-227 provides a practical 9–10 hours* of operating time. * Typical operation Tx:Rx: Stand-by=5:5:90
Other features
- 128 memory channels with 8 zones
- Inversion type*1 voice scrambler built-in
- Optional VOX headsets available
- Optional GPS speaker-microphone
- Power ON password
- Radio stun/kill/revive
- 8 DTMF autodial
- Normal and priority scans
- 2-step power saver and 2-step low battery beep
- BIIS 1200 mode programmable
- Busy, repeater lockout functions
- BTL only version (no vibration alert and no voice recorder) and BTL/Vibration alert version (no voice recorder) available*2 and more...
*1 Inversion type voice scrambler is not compatible with UT-109/UT-110 voice scrambler. UT-109/UT-110 cannot be physically installed into the IC-F50V. *2 Not available in some countries. (Not available in the U.S.)
|
|